In this document, we will cover how to properly configure your TP-Link Archer C1200 v3 for use with mDNS and multicast devices.
In this document we will cover how to configure a TP-Link Archer C1200 v3 with a TP-Link SG1008PE switch to properly enable discovery of the cameras and for use in a multicast environment.
Plug a network cable in between an available LAN port on the Archer C1200 v3 and an available network port on the network switch.
Plug the “Internet Port” of the Archer C1200 v3 into an available ethernet port on your cable modem or existing network.
Plug your PC into LAN port 2 on the Archer C1200 v3
Plug the Archer C1200 v3 and the network switch into available power outlets and turn them on.
We will now configure the Archer C1200 v3 using the routers “setup wizard”
Type “tplinkwifi.net” into the search bar of your internet browser.
You will now begin the initial step-by-step process of setting up your Archer C1200 v3 for use with mDNS and multicast devices.
Time Zone (Step 1)
Select your time zone from the drop-down menu and click “Next”
Internet Connection (Step 2)
For most users choosing Dynamic IP and clicking the “Next” button will provide success in the end…
An easy way to test and see if a Dynamic IP connection is likely to work for you is to temporarily plug an available PC directly into your modem. If you are able to access the internet when directly connected to the modem, then the Dynamic IP connection should work. Otherwise, you will likely need to use the Static IP option, which will require you to contact your network administrator or possibly your ISP.
MAC Cloning (Step 3)
The next screen allows you to clone the MAC address of your computer.
Unless your ISP instructs your to do this for internet connections, choose
“Do not clone my MAC address” and click the “Next” button.
Wireless Networks (Step 4)
In this step you can create a wireless network.
Note: We do not recommend running multicast sources through WiFi.
Only enable the WiFi feature if you need to share your internet connection with other devices and do not plan on using it for content delivery.
Summary and Commit (Step 5)
The final “setup wizard” page summarizes the settings you entered from above.
Check the settings as shown and click the “Next” button when you are satisfied with the choices displayed.
Click the “Save” button which will present a progress bar as the router begins to commit your settings and then finally restarts.
Note: It is recommended to enable cloud and local access to the device.
Once the device has fully rebooted log in to the WebUI of the Archer C1200v3 and click on the following options to continue with the setup process.
You should now see page as shown below
If you have a desired network scheme please proceed with setting up the network per your requirements.
If you do not have a specific network scheme you wish to use we recommend the following network settings.
IP Address: 192.168.100.1
Subnet Mask: 255.255.255.0
Since the default IP addresses of the PTZOptics cameras are within the 192.168.100.XXX scheme you should be able to reach the cameras straight from the box with the least setup steps required.
Click the “Save” button
IPTV Settings (Multicast)
Navigate to the “Network” and then “IPTV” section while still under the “Advanced” tab.
Click the box to enable “IGMP Proxy”
Under the IGMP Version drop down menu select “V3”
Click the box to “Enable IPTV”
Set LAN 1 and LAN 2 to “Internet”
Set LAN 3 and LAN 4 to “IPTV”
With this setup all cameras and or switches with cameras should be connected to the “IPTV Lans” (LAN 3 & LAN 4)
Any device that requires a connection to the internet through the router should be plugged into the “INTERNET LANs” (LAN 1 & LAN 2)
Click the “Save” button
You have now properly configured your TP-Link network for use with mDNS and multicast!
Please note we do not provide any support in relation to this document and take no responsibility for any impact or losses that may result from following this guide.